Welcome to the official website of Shanghai Sutian Plastic Mould Co., Ltd.!

National Service Hotline:


您當前的位置 : Home >> News >> company news

The main process parameters of plastic product processing manufacturers include


Shanghai injection manufacturer

With our application of plastics, the processing methods of plastics have always changed. Injection molding is one of our most commonly used plastic processing methods. After injection molding processing, we can process all kinds of products we want. When processing injection molded parts in Changzhou, molds are needed. After the molds are used, they must also be discontinued. Next, let's take a look at how to support the molds of these injection molded parts.

The surface of the mold can not be ignored. It directly affects the surface quality of the product. The focus is to prevent rust. Therefore, it is especially important to choose a suitable, high-quality, professional anti-rust oil. After the mold has completed the consumption task, different methods should be used to carefully remove the remaining injection molding according to different injection molding. Copper rods, copper wires and professional mold cleaning agents can be used to remove the remaining injection molding and other deposits in the mold, and then air-dry. Liquidation of hard objects such as iron wires and steel bars is prohibited to avoid scratching the surface. If there are rust spots caused by corrosive injection molding, use a grinder to grind and polish, and spray professional anti-rust oil, then store the mold in a monotonous, cool, dust-free place. At the same time, the focus tracking inspection of several important parts of the mold should be suspended. The function of the ejection and guide parts is to ensure the mold opening and closing movement and the ejection of the plastic parts. Insist on the lubrication of the mold thimble and guide post, and regularly check the thimble and guide post for deformation and surface damage. Once found, change it in time. After completing a consumption cycle, coat the mold's working surface, movement and guide parts Professional anti-rust oil.

It is very important to support these molds. If we do not do the mold support, it will definitely affect the quality of the next injection molding process, which will cause damage to the mold and affect the entire consumer work, so I hope everyone At the time of discontinuing the processing of injection molded parts, we can focus on the maintenance of the mold, extend the service life of the mold, and increase the quality of our injection molded parts.

停機 Stopping is unavoidable during the injection molding process, but the shutdown is not arbitrarily stopped. A qualified shutdown process must also be adopted to prevent affecting the molding of the injection molded parts. Of course, the startup after shutdown must also be qualified, otherwise the injection molding process cannot be stopped smoothly.

的 When the machine is temporarily stopped during operation, the remaining plastic should be sprayed repeatedly, or other plastics should be passed through the injection molding machine to clean the remaining plastic in the shooting cylinder. When the plastic fades, the number of sprays should be increased. If the equipment is to be stopped due to repair and stop, the heater of the shooting cylinder must be adjusted to a low value to minimize the possibility of thermal synthesis.

Since it has been stopped for a while, when it is restarted, it is only necessary to turn off the bottom slide and the heater of the shooting cylinder to make the shooting cylinder clean. After the nozzle is completely cleaned, try to cool the injection cylinder as high as possible. After the injection molding machine has completely cooled down, close the equipment, and the injection molding machine can be reheated again.

1. Process barrel temperature of injection molding parts: The melt temperature is very important. The temperature of the shot cylinder used is only a guide. Melt temperature can be measured at the nozzle or by air radiation method. The temperature setting of the shot cylinder depends on the melt temperature, screw speed, back pressure, shot volume and injection cycle. If you have no experience processing a particular grade of plastic, start with the settings. For easy control, the spray cylinder is divided into zones, but not everything is set to the same temperature. If the operation time is long or operating at high temperature, please set the zone temperature to a lower value, this will avoid premature condensation and shunting of the plastic. Before starting the injection molded part, make sure that the hydraulic oil, hopper blocker, mold and shot cylinder are at the correct temperature.

2. Injection molding process melt temperature: The melt temperature plays a major role in the activity of the melt. Because plastic does not have a detailed melting point, the so-called melting point is a temperature range in the molten state. The structure and composition of plastic molecular chains are different, so The influence on its activity is also different. The rigid molecular chain is more obviously affected by temperature, such as PC, PPS, etc., while the activity of flexible molecular chains, such as PA, PP, PE, etc. is not obvious after changing the temperature. Information to adjust the reasonable temperature of the injection molded parts.

3. Injection mold process mold temperature: Some plastic materials require higher mold temperature due to high crystallization temperature and slow crystallization speed, and some require higher temperature or lower temperature due to the size and deformation control or the need for demolding. For example, PCs generally request 60 degrees or more, and PPS sometimes requires 160 or more degrees in order to achieve better appearance and improve mobility. Therefore, the mold temperature is inevitable to improve the appearance, deformation and size of the product, and the rubber mold. effect.

4. Injection pressure of injection molding process: The resistance required for the melt to restrain the travel directly affects the size, weight and deformation of the product. Different plastic products require different injection pressures. For information such as PA and PP, increasing the pressure will cause Its mobility is significantly improved, and the injection pressure determines the density of the product, that is, the appearance of gloss. It does not have a fixed value, and the harder the mold is filled, the higher the pressure of the injection molded part.


Recently Viewed:

Shanghai Sutian Plastic Mould Co., Ltd.(R & D Center)

Suzhou Longyu Phaeton Auto Parts Co., Ltd. (production base)

Contact person: General Teng

Company phone: 021-67890578

Company address: No. 8 Workshop, No. 601 Xiangmin Road, Chedun Town, Songjiang District, Shanghai


 Follow the official WeChat Follow mobile stations
Copyright ? Shanghai Sutian Plastic Mould Co., Ltd. All rights reserved record number:滬ICP備19039722號